Plumbing 101: A Guide to Bathtub Installation
Plumbing 101: A Guide to Bathtub Installation
Blog Article
This post which follows involving How to Install a Bathtub Yourself is without a doubt attention-grabbing. You should keep reading.
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably difficult task. If the old bathtub is conveniently obtainable, the job can relocate speedily; if you have to open a wall surface to eliminate the old bathtub and also position the brand-new bathtub, the job is much harder. In either case, the job is within a home handyman's abilities, although you will need an assistant to vacate the old bathtub and set in the brand-new one. See to it you have actually qualified on your own for the task and fit trying it. Rather than hiring a professional to take over a halfway-completed task, it is much better to consider using one prior to you begin. Opportunities are you might require a specialist plumber to make tube links.
This post will help you mount a new bath tub in your washroom if you have already acquired a new tub and also don't require to alter the arrangement of your previous water system pipes.
Your devices and product checklist ought to comprise the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, then the first thing you should do is separate the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the restricted access that is often the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin making sure that the washing machines remain in place between the faucet and the sink. Secure the tap in place with the producer provided backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet adapters. The previous kind ought to be linked to the faucet finishes initially, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Utilizing the two wood boards under its feet, put the tub in the required placement. The wood boards are helpful in equally spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little factors.
The next objective is to make certain that the tub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the tub up until the spirit level checks out level.
To install faucets, fit all-time low of the outermost adaptable faucet connector to the suitable supply pipeline by making a compression join; then do the exact same for the various other faucet.
Activate the water supply and check all joints and also brand-new pipework for leaks as well as tighten them if needed. Fill up the tub and also check the overflow electrical outlet and the normal electrical outlet for leakages.
Lastly, take care of the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bath tub ought to wait up until the tub has actually been made use of at the very least once as this will certainly resolve it right into its final setting.
Preparing for the Installation
Firstly, the sustaining frame supplied with the bath needs to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to prevent strain on the bath tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you utilize every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must now prepare to be suited its final position.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to break an inflexible seal, causing the water to penetrate the wall surface between the bath and also the tiling, bring about difficulties with wetness and possible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and installations. They are sold in tubes as well as cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with spins of drenched paper or soft rope. Bear in mind to always load the bathtub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealer can crack rather early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly available on the marketplace. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that write up about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when exploring the web. If you please take the time to share this content if you enjoyed reading it. Kudos for your time. Come back soon.
Protect your property, call! Report this page